Most Recent Cisco 300-730 Exam Dumps

Prepare for the Cisco Implementing Secure Solutions with Virtual Private Networks exam with our extensive collection of questions and answers. These practice Q&A are updated according to the latest syllabus, providing you with the tools needed to review and test your knowledge.

QA4Exam focus on the latest syllabus and exam objectives, our practice Q&A are designed to help you identify key topics and solidify your understanding. By focusing on the core curriculum, These Questions & Answers helps you cover all the essential topics, ensuring you're well-prepared for every section of the exam. Each question comes with a detailed explanation, offering valuable insights and helping you to learn from your mistakes. Whether you're looking to assess your progress or dive deeper into complex topics, our updated Q&A will provide the support you need to confidently approach the Cisco 300-730 exam and achieve success.

The questions for 300-730 were last updated on Mar 30, 2025.

Viewing page 1 out of 35 pages.
Viewing questions 1-5 out of 175 questions

Get All 175 Questions & Answers

Question No. 1

Refer to the exhibit.

An engineer is troubleshooting a new GRE over IPsec tunnel. The tunnel is established but the engineer cannot ping from spoke 1 to spoke 2. Which type of traffic is being blocked?

AESP packets from spoke2 to spoke1

BISAKMP packets from spoke2 to spoke1

CESP packets from spoke1 to spoke2

DISAKMP packets from spoke1 to spoke2

Show Answer

Correct Answer: A

Question No. 2

An engineer must investigate a connectivity issue and decides to use the packet capture feature on Cisco FTD. The goal is to see the real packet going through the Cisco FTD device and see Snort detection actions as a part of the output. After the capture-traffic command is issued, only the packets are displayed. Which action resolves this issue?

ASpecify the trace using the -T option after the capture-traffic command

BPerform the trace within the Cisco FMC GUI instead of the Cisco FMC CLI

CUse the verbose option as a part of the capture-traffic command

DUse the capture command and specify the trace option to get the required information
B) Performing the trace within the Cisco FMC GUI instead of the Cisco FMC CLI is not a valid option, because the FMC GUI does not support packet capture or tracing on the FTD device. You can only use the FMC GUI to view and export captures that are taken on the FTD CLI1.
C) Using the verbose option as a part of the capture-traffic command is not a valid option, because there is no verbose option for this command. The verbose option is only available for the capture command, which is used to capture packets on the LINA engine domain of the FTD device1.
D) Using the capture command and specifying the trace option to get the required information is not a valid option, because the capture command does not have a trace option. The capture command allows you to capture packets on the LINA engine domain of the FTD device, but it does not show the Snort detection actions. The trace option is only available for the packet-tracer command, which is used to simulate a packet going through the FTD device and show its processing steps1.

Show Answer

Correct Answer: A

The correct answer is A. Specify the trace using the -T option after the capture-traffic command. According to the document Use Firepower Threat Defense Captures and Packet Tracer, the capture-traffic command allows you to capture packets on the Snort engine domain of the FTD device. However, by default, it only shows the packet headers and does not include the Snort detection actions. To see the Snort detection actions, you need to use the -T option, which enables tracing. For example:

capture-traffic -T

This will show the packet headers along with the Snort verdicts, such as allow, block, or replace. You can also use other options to filter or save the capture output1.

Question No. 3

An engineer is requesting an SSL certificate for a VPN load-balancing cluster in which two Cisco ASAs provide clientless SSLVPN access. The FQDN that users will enter to access the clientless VPN is asa.example.com, and users will be redirected to either asa1.example.com or asa2.example.com. The cluster FQDN and individual Cisco ASAs FQDNs resolve to IP addresses 192.168.0.1, 192.168.0.2, and 192.168.0.3 respectively. The issued certificate must be able to be used to validate the identity of either ASA in the cluster without returning any certificate validation errors. Which fields must be included in the certificate to meet these requirements?

ACN=*.example.com, SAN=asa.example.com

BCN=192.168.0.1, SAN=asa1.example.com, asa2.example.com

CCN=asa.example.com, SAN=asa.example.com, asa1.example.com, asa2.example.com

DCN=192.168.0.1, SAN=192.168.0.1, 192.168.0.2, 192.168.0.3

Show Answer

Correct Answer: C

https://integratingit.wordpress.com/2020/03/14/asa-vpn-load-balancing/

Question No. 4

Refer to the exhibit.

Based on the output of the show run command, which remote access VPN technology is configured?

APPTP

BSSLVPN Full Tunnel

CFlexVPN

Dclientless SSLVPN

Show Answer

Correct Answer: C

Question No. 5

Refer to the exhibit.

DMVPN spoke-to-spoke traffic works, but it passes through the hub, and never sends direct spoke-to-spoke traffic. Based on the tunnel interface configuration shown, what must be configured on the hub to solve the issue?

AEnable NHRP redirect.

BEnable split horizon.

CEnable IP redirects.

DEnable NHRP shortcut.

Show Answer

Correct Answer: A

Unlock All Questions for Cisco 300-730 Exam

Full Exam Access, Actual Exam Questions, Validated Answers, Anytime Anywhere, No Download Limits, No Practice Limits

Get All 175 Questions & Answers