Most Recent Dell EMC D-NWG-FN-23 Exam Dumps

Prepare for the Dell EMC Dell Networking Foundations 2023 exam with our extensive collection of questions and answers. These practice Q&A are updated according to the latest syllabus, providing you with the tools needed to review and test your knowledge.

QA4Exam focus on the latest syllabus and exam objectives, our practice Q&A are designed to help you identify key topics and solidify your understanding. By focusing on the core curriculum, These Questions & Answers helps you cover all the essential topics, ensuring you're well-prepared for every section of the exam. Each question comes with a detailed explanation, offering valuable insights and helping you to learn from your mistakes. Whether you're looking to assess your progress or dive deeper into complex topics, our updated Q&A will provide the support you need to confidently approach the Dell EMC D-NWG-FN-23 exam and achieve success.

The questions for D-NWG-FN-23 were last updated on Apr 14, 2025.

Viewing page 1 out of 12 pages.
Viewing questions 1-5 out of 60 questions

Get All 60 Questions & Answers

Question No. 1

What is an advantage of UFD?

AReduces connectivity loss.

BDetects the loss of downstream connectivity.

CReduces network complexity.

DPrevents the loss of upstream connectivity.

Show Answer

Correct Answer: D

Question No. 2

Refer to the exhibit.

No static routing has been configured. For iBGP loopback-based peering, which statement is correct?

AIt is not necessary for the routing table on S1 to have an entry for the loopback network of S3.

BS1 should have the Loopback network of S3 in its routing table for loopback-based peering.

CFor iBGP peering, physical interface addresses must be used.

DA static route on S1 to 144.254.32.1/32 will eliminate the need for loopback-based peering with S3.

Show Answer

Correct Answer: B

Question No. 3

A customer has disabled LLDP on the management interface of the switch. What is the proper command to re- enable it?

AOS10(config)# lldp enable OS10(config)#lldp transmit OS10(config)#lldp receive

BOS10(config)# interface mgmt 1/1/1 OS10(conf-if-ma-1/1/1)#lldp med enable OS10(conf-if-ma-1/1/1)#lldp timer 10

COS10(config)# interface mgmt 1/1/1 OS10(conf-if-ma-1/1/1)#lldp transmit OS10(conf-if-ma-1/1/1)#lldp receive

DOS10(config)# interface mgmt 1/1/1 OS10(conf-if-ma-1/1/1)#lldp tly-select OS10(conf-if-ma-1/1/1)#lldp dot1tlv

Show Answer

Correct Answer: C

Question No. 4

What are the correct steps to configure a static LAG on a Dell Networking OS10 switch?

Ainterface port-channel 4 channel-group 4 mode passive
interface range ethernet 1/1/14-1/1/15 channel-group 4 mode on

Binterface port-channel 4 channel-group 4 mode on
interface range ethernet 1/1/14-1/1/15 channel-group 4 mode passive

Cinterface port-channel 4 no shutdown
interface range ethernet 1/1/14-1/1/15 channel-group 4 mode on

Dinterface port-channel 4 no shutdown
interface range ethernet 1/1/14-1/1/15 channel-group 4 mode active

Show Answer

Correct Answer: C

Question No. 5

You have been asked to examine a BGP configuration for a co-worker who is having difficulty establishing BGP peering. The address shown is that of the neighbor's Lo0 interface. Given the configuration shown, what would be your recommendation?

S3(config-router-bgp-65042)# neighbor 192.168.32.1

S3(config-router-neighbor)# remote-as 65042

AModify the existing configuration to be:
S3(config-router-bgp-65042)# neighbor 192.168.32.1/24 S3(config-router-neighbor)# peer-as 65042

BAdd the following to the existing configuration: S3(config-router-neighbor)# update-source loopback 0 S3(config-router-neighbor)# no shutdown

CIssue the no shutdown command and verify that the BGP state is ESTABLISHED

DIssue the no shutdown command and verify that the BGP state is ACTIVE

Show Answer

Correct Answer: C

Unlock All Questions for Dell EMC D-NWG-FN-23 Exam

Full Exam Access, Actual Exam Questions, Validated Answers, Anytime Anywhere, No Download Limits, No Practice Limits

Get All 60 Questions & Answers