Most Recent Fortinet FCSS_NST_SE-7.4 Exam Dumps

Prepare for the Fortinet FCSS - Network Security 7.4 Support Engineer exam with our extensive collection of questions and answers. These practice Q&A are updated according to the latest syllabus, providing you with the tools needed to review and test your knowledge.

QA4Exam focus on the latest syllabus and exam objectives, our practice Q&A are designed to help you identify key topics and solidify your understanding. By focusing on the core curriculum, These Questions & Answers helps you cover all the essential topics, ensuring you're well-prepared for every section of the exam. Each question comes with a detailed explanation, offering valuable insights and helping you to learn from your mistakes. Whether you're looking to assess your progress or dive deeper into complex topics, our updated Q&A will provide the support you need to confidently approach the Fortinet FCSS_NST_SE-7.4 exam and achieve success.

The questions for FCSS_NST_SE-7.4 were last updated on Feb 22, 2025.

Viewing page 1 out of 8 pages.
Viewing questions 1-5 out of 40 questions

Get All 40 Questions & Answers

Question No. 1

Exhibit.

Refer to the exhibit, which contains a screenshot of some phase 1 settings.

The VPN is not up. To diagnose the issue, the administrator enters the following CLI commands on an SSH session on FortiGate:

However, the IKE real-time debug does not show any output. Why?

AThe administrator must also run the command diagnose debug enable.

BThe debug shows only error messages. If there is no output, then the phase 1 and phase 2 configurations match.

CThe log-filter setting is incorrect. The VPN traffic does not match this filter.

DReplace diagnose debug application ike -1 with diagnose debug application ipsec -1.

Show Answer

Correct Answer: A

Question No. 2

Refer to the exhibit, which shows the output of a debug command.

Which two statements about the output are true? (Choose two.)

AThe interlace is part of the OSPF backbone area.

BThere are a total of five OSPF routers attached to the vorz4 network segment

COne of the neighbors has a router ID of 0.0.0.4.

DIn the network connected to port4, two OSPF routers are down.

Show Answer

Correct Answer: A, D

Question No. 3

Refer to the exhibit, which shows the output of get router info bgp summary.

Which two statements are true? (Choose two.)

AThe local ForliGate has received one prefix from BGP neighbor 100.64.1.254.

BThe TCP connection with BGP neighbor 100.64.2.254 was successful.

CThe local FortiGate has received 18 packets from a BGP neighbor.

DThe local FortiGate is still calculating the prefixes received from BGP neighbor 100.64.2.264

Show Answer

Correct Answer: A, C

Question No. 4

Refer to the exhibit, which shows the output o! the BGP database.

Which two statements are correct? (Choose two.)

AThe advertised prefix of 10.20.30.0'24 was configured using the network command.

BThe first four prefixes are being advertised using a legacy route advertisement.

CThe advertised prefix of 10.20.30.0'24 is being advertised through the redistribution of another routing protocol.

DThe output shows all prefixes advertised by all neighbors as well as the local router.

Show Answer

Correct Answer: A, D

Question No. 5

An administrator wants to capture encrypted phase 2 traffic between two FotiGate devices using the built-in sniffer.

If the administrator knows that there Is no NAT device located between both FortiGate devices, which command should the administrator run?

Adiagnose sniffer packet any 'udp port 500'

Bdiagnose sniffer packet any 'lp proto 50'

Cdiagnose sniffer packet any 'udp port 4500'

Ddiagnose sniffer packet any 'ah'

Show Answer

Correct Answer: B

Unlock All Questions for Fortinet FCSS_NST_SE-7.4 Exam

Full Exam Access, Actual Exam Questions, Validated Answers, Anytime Anywhere, No Download Limits, No Practice Limits

Get All 40 Questions & Answers